Professional manufacture of acrylic bahtub and shower cabin in China.

considering a bathroom installation

by:Xavier      2020-04-04
The main focus here is the installation of the bathroom, especially the installation of the shower or bathtub, the casing of the bathtub and the surround installation of the bathtub.
But before anything else, let\'s take a look at some bugs and recommended guidelines that are common in bathroom installations.
The most common mistakes and guidelines for bathroom installation observe many common mistakes from most bathroom installations.
The following is a list of these errors: ignore or violate local regulations to limit the use of a pipe that is too small to connect copper to the galvanized without the use of brass or dielectric fittings between the two. Does not take into account the Teflon tape or piping compound, especially the air gap filler of the thread joint not installed the fixing device does not properly align the pipe to the fitting or the cut-off valve to cut off the supply stub too short, the shut-off valve cannot be installed after the completed wall is in place. After knowing these errors, uneven fixtures when installing them, I think you \'d better know some of the standard improvements that the federal government has put in place for those who want to go to the toilet.
Please note that whether you are planning to design a bathroom for a wheelchair or just to make the room more comfortable and practical for people with mobility inconveniences, these standards are very applicable.
Here are some recommended guidelines: From the moment you enter the room, I know that you want to make sure that the door is as low as 32 inch wide.
If you find that the door is located next to the corridor and you have a wheelchair that has to be changed from the hall to the door, the width of the door must be adjusted to about 36 inch.
Also avoid setting a threshold at the door if possible.
However, if a specific threshold is required, you can choose a flat threshold that does not exceed inches high, or, perhaps, is oblique on both sides and does not exceed inches high.
If you have a member with limited hand strength in your home, standard door handles can be hard to catch.
So, the usual suggestion is to choose the lever handle instead of the knob.
The height of this handle must be 48 inch or less above the floor.
Bathroom fixtures are different from traditional toilets, traditional toilets are about 14 to 15 inch above the floor, you can use barrier-free toilets designed and developed with seats between 17 and 19 inch above the floor.
For the sink, you may want to make sure that the edge is not above 34 inch above the floor.
In addition to this, the sink should reach out at least 17 inch from the back wall, the area under the sink must be opened, with at least 29 inch clearance from the floor to the bottom of the sink.
If you want your sink to fit on the countertop, consider placing no more than 2 inch from the side of the counter.
According to some experts, this promotes maximum accessibility.
In addition, you can use protective boots on water lines and traps under the sink to prevent contact. Use a single-handle, lever-
A closed fist easily operated style faucet.
Many homeowners think the sheets vinyl flooring is the best option.
The main reason may be its smooth quality and easy cleaning.
However, if you are using a tile, try choosing a large and smooth tile, which can reduce the grouting line and some surface irregularities.
Also find a non
Smooth texture.
Also, stick to a nap if you\'re thinking about paving the floor.
This is another suggestion for those driving wheelchairs.
Well, let you do a 180-
When turning, the wheelchair needs at least 60 inch clearance, that is, 5 feet clearance.
Note that this clear space is often difficult to implement, but consider a T-
Space is shaped.
Each side of T must be at least 36 inch wide.
According to some experts, this configuration will allow the wheelchair to have the space to comfortably make three
Point the turn instead of having to maneuver in a full circle.
With this in mind, try to go to any fixture that is at least 36 inch wide.
And, when it comes to the sink, there should be a clear space in front of it.
Perhaps one of the wonderful things in almost any bathroom is the armrest bar.
These even make the bathroom safer and more convenient for anyone to use.
Well, it\'s worth noting that if you\'re installing a horizontal grab bar, it should be on the wall behind the toilet.
You can install another one on the closet side wall next to the toilet.
Also, the handrails should be placed inside the bathtub and shower.
If you are renovating or installing a new one and the walls of the room are open, make sure there are blocks of wood on the walls.
This simplifies the connection of the grab bar.
Well, these guidelines are enough.
Now, let\'s start with some steps to install a shower or bathtub.
How to install the shower and bathtub when considering installing the shower or bathtub, it should be noted that the required pipes include hot and cold supply lines, in addition to the pipes leading to the shower head.
In addition, many experts often recommend the installation of mixing valves and shower heads, including air chambers.
Typically, in fixtures, the rate of the bath or shower fixture is lower.
As a result, they are usually placed on the branch drain and discharged to the wet or back like a sink.
Therefore, due to the angle at which the floor trap is located, both the shower and bathtub enter the stack on or below the floor.
When it comes to the faucet and shower head assembly, one should note that it needs a wall with an opening to be installed.
There is also a concern that the bathtub and shower may need a support frame.
A common idea here is that a bathtub full of water is very heavy;
Therefore, it is important to first check the building specifications, including the frame support, before the bathtub is installed.
A floor area is also required for the shower.
According to some experts, an area of at least 1,024 square inches is required, but you should also allow a distance of 24 inch from the booth itself to any other fixture or wall.
The basic principles are as follows: 1.
All pipes should be installed before installing the Bathtub itself. 2.
Lower the bathtub.
This will allow continuous flanges to be installed on wall posts and on 1x4 or 2x4 brackets.
In connection with this, do not forget to fix the bathtub on the shell with nails or screws, and fix it on the bolt through the flange. 3.
Connect the drain pipe.
This can be done by connecting the tub overflow to the tub drain above the trap, not above the trap.
Note that the trap will have a compression fitting that is screwed on the arm of the overflow assembly. 4.
Connect the hot and cold water lines to the tub or shower mixing valves that connect them.
You can do this by sweating these directly to the hot and cold ports of the mixing valve. 5.
Install a tube on the wall for the shower head.
Note, however, that at the top of this pipe you should sweat on the brass female threaded wing fittings that are nailed or screwed into the frame bracket. 6.
A 1/2 tube should be extended, but this must comply with the instructions provided by the manufacturer for the Bath spout.
In addition, sweat on male threaded fittings at the end of the pipe, or use brass nipples of the appropriate length and a cover of 1/2. 7.
At this point, you need to check your rough pipe. 8.
Restore the water pressure and check the drainage connection, including whether there is a leak in the water supply pipeline. 9.
Replace the wall with a moisture-proof drywall as the basis for the wall covering.
Also note that the seam between the wall and the new tub is sealed with a silicone caulking agent.
This filling will prevent water seepage. 10.
Now is the time to install the handle, shower head and spout.
Please note that the shower head is screwed on the shower arm stub.
And, whether you install a new shower head or replace the old one, clean the pipe thread and apply the new pipe joint compound.
To prevent leakage, you can also consider using Teflon tape or both.
You may know that the bathtub is installed around the bathtub (
Commonly known as wall kit)
Is an easy way to provide beauty, waterproofing and easyto-
Keep the barrier around the bathtub or shower niche.
These can be placed around plaster, tile, drywall or any solid and flat wall.
Well, there are some surround kits on the market right now.
Most kits contain three or five overlapping parts to take into account different sizes.
Also, these kits include instructions that you should consider reading before you leave the store.
You may need adhesive and color when installing the bath surround-
So consider buying these from the store.
Installing the bathtub casing first is a necessary finishing work
In the bathtub or Jacuzzi.
So, if you\'re thinking about these types of bathtubs, then consider installing a shell.
Installing the Bath case is actually not as difficult as it looks.
Even if you have a bit of skill, of course you can build it with the right material.
Consider the following: one of the most important considerations when building a bathtub enclosure is the type of bathtub.
Especially down-
In the bathtub specially made for the Bath case, it is said to be the best choice.
However, the Jacuzzi is also perfect for the surrounding buildings.
A shell is basically necessary to hide the water pipe on the water drop
Jacuzzi and Jacuzzi.
So when you consider building a pipe, be sure to work around the pipe and the drainage system to avoid interfering with the pipe. That\'s all!
So, good luck with your bathroom installation project.
Custom message
暂无友情链接数据
Chat Online 编辑模式下无法使用
Chat Online inputting...
Dear customer, Due to the large number of inquiries, we may not be able to reply you in time. You can describe what you want, and we will reply you in time.